... The following is a guide to systematic maintenance of wind heaters in the forest that do not break fire**, which i interpret in order of operation and efficiency, taking into account the working principles and operational experience of the wind machine system:
I. Quick-tracking of malfunctions (three-minute preliminary diagnosis)**
1. Audience
1. No sound: failure due to power/master plate failure (check 220v input)
2. Wind machines turned but no ignition: electromagnetic valves/firing firearms failure
3. Acoustic non-gas: gas valve congestion or ratio valve failure
Check out the fault code for reasons
- **e1/e2**: wind pressure anomaly (70% of failure)
- **11**: fire failure (ignition system problem)
- **12**: flames detection failure (incidental needle failure)
Ii. Phased maintenance operations (with special breakdown focus on wind)
Step 1: exclusion of underlying issues
1. **check three elements of gas**:
- ... Is the gas valve fully open (manual rotation 90° confirmed)
...- gas spares >10m3, gauge battery voltage >2. 6v
- unreconciled gas pipeline
2. ** hydraulic testing**:
- >0. 02 mpa (approximately 1. 5 litres/minute)
... - low water pressure areas: cleaning out of water filters (cleaning stainless steel filters with toothbrush)
Step 2: wind machine system overhaul (key!)
**facilitation performance**: wind engine inverts/ slows/acoustics
| point of detection | operational scheme | tool |
Capacitive malfunctions: chl (referred to as 1. 5 μf > 5%)
Capacity <1. 0 μf = replacement of the same-specified capacitor (resisting of 450 v)
The wind machine's dead: the hand-drive wheel
... If the brakes are turned, clean up the oil stains (wd-40 lubricants)
... If the wind-pressure switch fails, the short switch can be judged by two steps (blue/yellow line), sharp-mouthed
If you can light a fire after a short relay, replace the wind switch
3. Smoke blockage: dismantling pipe check (focus bend)
♪ bang, bang, bang, bang, bang ♪
> ** ironic windmill operation**:
> - power discharge ** (chronic screwdriver short lead)
- don't force the electric tester to avoid burning the main plate
Step 3: in-depth overhaul of the ignition system**
**1. Firecracker maintenance (code 11/12)**
- ** location correction**: distance sensors 3-5 mm (fingernail thickness), 45° angle of fire
- ** carbon cleaning**: sandpaper to metallic reflection (no shaving
- ** high pressure test**:
Electro-voltaic output of all instrument-point firearms:
Normal value: ≥12kv (arc length > 8mm)
Replacement of firearms below 8 kv
2. Electromagnetic valve detection (no gas output)**
...-- ** coil barrier**: red/black line detection value removed (normal 15-25)
- ** valve congestion**: alcohol-cleaning valve core (tamp-marked wipe)
3. Flame sensors (code 12)**
- ** on-site testing**: 10,000 meters of needles and outer-hull electrical resistance (should be 0)
-** signal voltage**: cyclops on fire > 1. 5v (less than 0. 8v to replace)
Iii. Step-by-step failure management (main plate maintenance)**
Three axes tested on the main panel**
1. **electron power measurement**:
- transformer output: ac 30v (winder)
- pressure chip: 7805 for dc 5v ± 0. 2v
2. **fire signal**:
- fire flash: the ignition end should have a 3-5v pulse (shower detection)
3.** proportional valve control**:
- normal voltage: 2. 8 v after ignition at 0v
> ** hazardous operation alert**:
>if scale valve voltage continues > 3v,** immediate power outage* indicates that the main plate is out of control and the gas valves are at risk of explosion
Maintenance flowchart**
There's no fire
"b" wind
"b" is "c"
Short wind pressure switch
C-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-e-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-c-
Switching wind
The c-c-c-c-c-c-c-c-c-c-c-c-c-e
Check the needle voltage
B-o-o-o-f
Measurement of capacity
"f--"g."
Change your face
F-o-o-h
Manually turn the wheel
I'm sorry
Oil purification/windie-offers
H-l-l-l-l-l-l-l-l-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i-i..
Survey main panel 30v output
** post-maintenance certification standard**
1. **fire speed**: < 8 seconds to ignite (15 seconds allowed for initial start-up)
2. **flammation state**: blue cone (yellow flame = incendiary)
3. **emissions**: no black ash from smoke vents (30-second ash from paper test)
... The mastery of this program will solve 95% of the wind engine-type ignition failure。
