# headline creation challenge #
Recently, friends have shown that the toilets in the house are always leaking and are accompanied by retortion。
As a result, a friend's toilet was specially visited by his family's groceries. When the toilet was removed, problems were found。
These are also the most important details of toilet installation. So if you have a toilet in your house, do not be a viewer, but keep an eye on it。
Here's a groceries to share four details that need to be focused when the toilet is installed。
(i) the height of the sewers should be handled correctly
The first problem that leads to leaks and retorts in the toilet is the sewer。
Here's the sewer, which we have in the bathroom。
Our home is usually renovated with a sewer pipe with a diameter of 110 millimeters and condensed from the ground. This sewer is used to install toilets。
And the height of the sewers must be handled correctly. If not properly addressed, problems arise。
One, the sewers are too low
At this point, the toilet can't be sealed with the sewer. The end result of this problem is a leak, which always comes out of the toilet, with the taste of time。
The root cause of the problem was that there was no connection between the sewers and frank, which were separate. So it doesn't work as an effective seal。
Two, the sewers are too high
If the height of the toilet pipe is set at more than 10 centimetres, the problem may not be apparent for a short period of time after the toilet is installed. It's been a long time and the toilet may be loose。
The root cause of the problem was the lack of close contact between the toilet and the ground, with a slight tilt. As we use it, it causes the toilet to shake。
Correct practice:
1. High-level tailoring of sewers shall be appropriate. The majority of toilets were installed, requiring sewers to be completed approximately 10 cm from the ground. You can keep it longer, and you can tailor it when installed。
2. In the course of the renovation, it is important not to allow the decorator to flatten the sewer pipe. This will make the installation of our toilets very difficult and easy to see through。
3. If the sewers are too low, it is recommended that you proceed to the upper and lower sections when you install toilets. That is to install a section on the original sewer and then cut to 10 centimeters。
(ii) close the sewers. When
The second problem that tends to cause leaks in toilets is inadequate handling around the sewers。
In fact, one might also find that there is a gap between the sewers and the tiles after they have been renovated. And it's basically cement sand in the cracks。
However, the teacher who installed the toilet did not give special treatment to this gap. When installed, it was installed directly in farah and then placed the toilet seat above it。
This problem may result in minor leakage and infiltration into the building along the sewers. Then we looked upstairs for a leak, and we couldn't find it。
Thus, when toilets are installed, the disposal around the sewers is checked in advance and is handled in accordance with the correct requirements。
Correct practice:
Before the toilet is installed, it is recommended that you check the gap between the sewer and the tiles. If there is loose cement sand in it, these loose cement sands should be cleaned up。
2. It is suggested that, in the case of dry cracks, seals may be placed in seals. For example, we can punch in glass and fill the sewers. Or you can use the leak king directly to level the gap between the sewer and the tiles。
3. When we install the toilet, we have to check the glue we hit or the leak king is completely dry. And close seals between the tiles and the sewers。
(iii) frank chose right
The third issue that is very likely to cause leaks and retorts in the toilet is the choice and installation of frank the toilet。
Like the current toilet installation, generally a bowl of buttoned flanges is installed below. Frank is connected to the reserved sewer and then to the toilet。
If fran chose or installed inappropriately, there would be a gap between the toilet and the sewer。
The presence of this gap is slowly accompanied by leaks in the toilet and the retort of the toilet after a long period。
So the third thing you need to focus on when we install toilets is the choice and installation of toilets。
Practice guidance:
First, it is recommended that you abandon the more common rubber flanges. Like a lot of common toilets with farah, it's basically rubber. Rubber flanges are very susceptible to decay and break-ups, with long periods of time, and may seepage。
2. The second suggestion is that one should focus on not choosing the regular french. In other words, the length is the ordinary length, and this type of french connection is not particularly secure. So it's better to choose a longer frank。
3. In the case of toilet flanges, the individual suggested that you should choose a thicker and longer rubber flanges. Rubber mud flanges have a certain ability to deform and are used as high-pointed rubbers with particularly strong binding capacity and no problems of cracking and ageing。
(iv): the glass glue should be used correctly
The last thing to make sure the toilet is fixed and sealed is glass。
It is estimated that many of the friends who were watching the toilet were able to find the trainer putting the toilet seat on the ground and then put a glaze around the toilet。
This glass glue is the key to securing the toilet on the ground, so it's also a matter of attention。
If the glass is not properly selected or used, the following problems generally arise:
1. The glass is broken. At that point, you will find that the glass glue around the toilet is separated from the ground, fractured, very ugly, and darkened。
Two, toilet shakes. The root cause of toilet shaking is the failure of the glass. Because glass glue can't hold up with the ground, and then when we use the toilet, there's a slight shake。
3. Leakage. When the toilet swayed, slowly there was water seepage under the toilet. It's been a long time, and it's all the same。
Suggested practices:
1. The glass glue used for toilet installation must be of good quality. It is suggested that you choose some of the famous branded glass glue. Like this, a tube would cost about $20, or even more。
The glass glue in the toilet, as much as possible, is selected against the mold. Because of the position of the toilet, if it is not acne-proofing and the time is long, the toilet is darkened and ugly。
3. The ground must be emptied during the glazing. The right thing is that when the toilet is installed, we wipe around the toilet with dry rags and then with dry paper towels. Until it's dry, then you hit the glue。
Following the glazing, it is recommended that you not move toilets for 24 hours. The toilet is stabilized on the ground and the glass glue is naturally condensed in order to achieve better results。
It's at the end
The toilet, although simple to install, raises many problems if the details are not properly controlled。
In this article, four details of the problem with toilets were highlighted. If you plan to install toilets in your homes, then you must keep an eye on them。
