Turn on the menu first: there's the direct point of the "replaced carbon powder box"
The newer types of the benevolent charts, such as p3010, p3300, m7100, m7300, contain the option of repositioning in the control panel. Press the menu key to find the system settings or the maintenance key and press ok to enter. There is a "replaced carbon powder box" in which some of the solids are written as "replaced selenium drums" or "carbon powder cartridges" and the selection is made by " ok", and the screen asks "whether to reset?" the machine will be restarted and the carbon count will return to full。
The word "replace" cannot be found in the menu. The solidware menus vary widely among the different batches of the chart, with only the depleted materials information (standing information) to see the remaining amount, with no duplicate buttons. This goes straight to the next section, using mechanical methods。
There's no placeline on the menu. The gears on the side of the drums
The aluminum drums tl-420 and tl-5120 have a half-turned white gear, which is a mechanical counter. Turn off the printer, open the forelid, and pull out the drums. Found this gear at the end of the drum (usually on the side without chips), turned it to the end with a single-word screwdriver, heard the sound of a “twirl”, the gear was stuck and the reset was completed。
Put back the selenium drums, close the front cap and turn it on. The screen may also show " insufficient carbon powder " , leave it alone and print directly by " ok " or " continue " . Some of the machines would require “replacement of selenium drums” to indicate that the gears were not identified or that the chips were locked, and would then look at the next section。
Keep your hands steady when you turn gears. The plastic teeth are very thin, and your head breaks. Don't lose it if there's a spring or a button next to the gear. Before reloading the selenium drums, shake the americium drum so that the carbon powder is evenly distributed, and the printing is clearer。
It's the wrong gear and the wrong chip
It's a one-time penetrix chip. It's locked to death when it's counted. It can't be broken. It's time to change the chip, or just the new selenium drum. The purchase of chips recognizes the drum models tl-420, tl-5120, tl-419, tl-413, etc., which are not universal and are not recognized on the wrong package。
It's not hard to change chips. Take out the selenium drums and find the chip - a small circuit board, two screws or a plastic card button. Take off the old chip and load the new chip back in the same direction. Don't turn back. Reload the selenium drums, turn them on, most of the machines will automatically identify, and the remaining quantity returns to 100 per cent。
Compared to other brands: most of the hewlett-packard machines rely on chip count, which must be replaced by chips or permanent chips after powdering; brother parts of gear can be reset without moving chips; some machines are thought to be clean directly in the drive or in the menu; and the energy, some parts of applet also have menus. In the early stages of the chart, tristars are taught with gears; the new machine begins to reset the menu, but the chip is still locked in a different chip。
There are three first steps to be taken after the zero zero zero zero zero zero zero zero zone zone: no zone zone zone zone zone zone. The "front cover open" is not closed and the "carbon powder box is not installed" is not actually reported by the drums. The chip points are covered with dry cloth, not alcohol. It is not possible to restart the printer or to implement the "recover the plant settings" in the menu. All attempts have been made to make a mistake and to contact the map for sale so that the drums are not removed。
Common question answers
How long will the carbon powder last
Zero is just zeroing the counter, and the amount of carbon is still the same. If there is still powder in the drums, it can be used until it is finished; if it is empty, printing becomes light or even blank, with powdering or changing the drums. Once zero is zero, several hundred more pages can be devoted to the remaining powder。
How can bento m6500 drums be eliminated
M6500 uses tl-420 simulets. First test menu: press the menu key to insert "system settings" in "maintenance" in "system settings" in "systems" in "systems". If this is not the option, remove the selenium drums and reset the gear side by side. Change the chip. The chip type recognizes tl-420。
Can the bentula drum chip be reused
The original chip is a one-time chip, which is locked when counted and cannot be used directly. Permanent chips or double chips are on the market and no longer counted, but may affect warranty. If you add your own powder, it would be better to have a matching model of permanent chips and save each one zero。
Do you still have to print the chart printer 'carbon box'
Yes, but depending on the type. Some machines are merely warnings, and can still be hit by “sure” or “continue”; others are stopped directly. The menu contains "ignorable carbon powder" or "continue printing" so that it can be activated. However, the quality of the printing will decline and it is recommended that the drums be powdered or replaced as soon as possible。
What's the difference between bentos and hewlett-packards
Hewlett-packard relies mostly on chips and zeros are basically the same as chip changers; brother-to-brother gears are able to reset; three stars in the early stages of the bengeogram, with gears, are available in the menu. I think some machines can be reset in the drive. It's a different brand。
Summary
Bentooth drums turn on the menu with a "replaced carbon powder box" directly; the repositioning gears on the side of the silhouettes are not transposed; the gears are misreported and chips are replaced. Don't come up here and start with the chips. If you add powder, switch the chip to a permanent chip, and it'll be all right. The machine is still under warranty, and after it has been prioritized for sale, self-dismantling of selenium drums may affect the warranty。
