3rd gradeHandmadeOne. Material for simple plastic cups of light: plastic cups, spent pens, drink covers, hot-melted guns, little scissors, cotton cloths, hooks, carpentry concrete processes: press the prep materials, one-time paper cups, coke caps, one-time pens, cotton, hooks, flowers in one-time cups
Handmade in the third grade
One. Simple plastic cup light
Material needed: plastic cups, spent pens, drink covers, hot-melled guns, scissors, cotton cloth, hooks, woodwork glue
Specific processes:
Press the prep, one-time paper cup, coke guy, one-time pen, cotton, hook flowers
Wrap the cloth around the one-time cup and cut out a rectangle suitable for length ratio
Sticking cotton cloths to one-time cups with plaster. Paper cups are trimmed at both ends. They are glued to the top, taped to the edges, covered in the cotton nodes
Because of the design logo tattoos on the white juice cap, it's covered with the same color of acrylic paint
Cut the ink off the trash pen with a little scissors and take off the red covers in the back
When the heater is heated, the milligram is glued to the top of the cup and to the cap, respectively。
The one-time cup has turned into a nice little light。
Ii. Simple little red lanterns
Ready materials:
One paper cup, a few red wires, small scissors, glue or tape, right-hand swingers left over the fireworks, red acrylic paints and paint brushes。
Specific steps:
Take a one-time cup and try to re-select it with only suggested reference. The vertical white stripes are evenly cut into a thin stripe。
2. Short, short and redundant cup edges。
3. To remove the emptiness, since the cup of coffee is wider。
More than a dozen spasms shrunk to the outside。
Take another one-time cup, only the top part of the original, and cut the rest。
6. The same pattern is cut and ready for docking with previous fine stripes。
7. First through the red line i in the opening slot in the five low-banded area, then through the six paper cup strips to the adhesive and the red lanterns are basically formed. It's more felt when you stick coloured cardpaper on the whole middle and you put a lantern on the bottom. A red lantern can be painted with water paint as a happy blue。
What about handmade paper cups
Cut two cups through the proper cut, one in half, the other in the bottom, the other in the bottom
It's a very popular painting on half the plastic cup
The ore materials that have been cut are not to be thrown off in a hurry, but are useful, and the stitches of the remaining materials are used as a lamp。
A little bit of this long note
The street lamp pole and the lower part of the floor are fixed with transparent tape。
The lampposts and the lights are fixed. The tape is not working. Use a stapler. On the head of the base and the lamppost。
It's done
One-time cups to make fine little lights
Methods of production:
I. Preparation of materials, one-off paper cups, drink covers, pens, rough cotton cloths, lace edges。
2. Wrap the cloth around a paper cup and cut out a square of a suitable length equal to that of a square。
Iii. Sticking cotton sheeting with glue on a paper cup, with appropriate cut-out at the top and bottom of the cup。
Iv. Placing all of them with white emulsions, glued laces and covered with cotton。
5. When the glued gun is heated, the coyote is glued to the bottom and the top to the bottom of the glass and bottle cover, respectively。
Another good way:
Put a one-time cup on a high-foot cup to see if it's fit, if it's right, and cut the top of the next sex cup, like this. Water pens are drawn in cups that are cut, and can also be written, with particular attention to the reverse。
No hints: if you don't write the opposite, you can draw the drawings, and it'll be a little bit easier. Put the flat-turned candle in the back of the high-foot cup and put the painted glass on top, and it can be finished。
