It's an automatic flush sensor in the bathroomRationaleIt is the use of infrared sensor control, the use of electromechanical combinations to achieve automatic flushing and control the size of the flush. Infrared sensor toilet automatic flushing, using infrared reflectivity, sends a reflection from an infrared launcher once the body's hands or body are close to the infrared area, and the infrared receiver integrates a microcomputer processing signal within the line and sends it to a pulsed electromagnetic valve。
Water toilets, which are now used by households, have been removed from traditional toilets. The advantages of such flush toilets are enormous, for example, that they are very clean and that they can be used to drain stolen materials without creating a “smelling” state of air in toilets. In addition, the flush toilet has a lid on it, which you can cover when you do not need to use. It also prevents the water in the toilet from exacerbating the humidity in the room. Now, let's get to the point where we're going to get to the toilet。
I remember one lesson about the water in the northern and southern hemisphere caused by geo-diversion. In a static state, there's a slight variation in the counterclockwise, and then there's a flushing toilet. In order to be able to clean up the stains thoroughly during the flushing, it is deliberately creating a powerful spray flow. But that's just the part of the toilet that we can see in our eyes, and his nature, more like a miracle of technology, is a magical water treatment system。
Almost everyone uses toilets now, and how many people know how to pump toilets for so long? The general flushing toilet consists of a pipe, a pipe, a permeable pipe, a plug (in and out), a float, a hose and leverage. The formation of a water tank can be seen as a system in its own right, operating in a very simple way, relying mainly on floats and plugs to control the recharge: float drops when the plug is pressed and the vent begins to fill, and when the water is filled to the height, the ball can block it from continuing。
And the system at the heart of the flushing toilet is its iris. There's an s-shaped pipe below it called a rainbow straw, and many people, or simply, think it's just a liquid seal-in-the-gas. When there is enough water to get through the tube, it can cause rainbow ingestion. The water in the barrel follows the tube, flips through the mouth of the drum higher than the liquid surface and goes lower outside the barrel, i. E. Up and down, until all the water in the barrel flows. This can be a good way to clean up the inside of the toilet. There must be enough water to pour in the sink at a sufficient speed to create a visible rainbow intake. So the key to the tank is to remove the water from it quickly enough in a short period of time to produce enough rainbow inhaling effect to take away all the water and sewage from the sink together。
According to the information, there are currently four main forms of flushing: straight-down flushing, general rainbow flushing, spray rainbow pumping and vortex flushing. The toilets that we usually see are vortex-based, characterized by low noise, and the vortex of flushing discharge. Instead, it is the impact of washing water that directly removes the contamination。
In contrast, the spraying of iris is designed to accelerate the discharge of sewage by venting water from underwater vents. With the help of atmospheric pressure, irritation occurs quickly to form the height differentials of the liquid column, resulting in strong stress differentials, moving liquids from high water levels under stress to low water levels under stress, and being filled with pipes that generate iris, and then into the air until all liquids are discharged. The sooner the rainbow is formed, the faster it occurs, the less efficient it is to lose water, the longer it lasts, the better it is to drain and save water。
In fact, many of the things we're exposed to in life are scientifically sound, and toilets are no exception. It is not for these things to be used to the old days, not to care about the mystery, to discover it, to truly gain from life。
The prices of flush toilets sold on the market varied, and good brand toilets were efficient and did not create a state of blockage, but prices were also more expensive. However, there are some cheap flush toilets where “powerways” are too small and sewage is too small to create a state of blockage. We need to do a market survey in advance when we're shopping for toilets. When you buy a toilet, you have to buy two mattresses to replace it, so it's more hygienic。
The operation of the flushing toilet is to use the gravity of the water, and when the toilet is completed, the discharge button on the tank is pressed, and the push button is used to pull the plug through the lever. The water in the tank will come out and run away。
When the water in the tank is cleaned, the plug itself falls and blocks the water. The ball then went down with the water in the tank, pushing the lever to pull the pipe out of the pipe and put the water in the tank for the next use。
The s bend of the pumped pipe below the toilet is the bend below the urinator, and when the tank drains the sewage, the water in the tank comes out beyond this s bend, creating a sorbence and flushing away the dirty water and the sewage. Until when a small amount of water was left behind, the flush stopped, leaving a little water sealed。
The toilet maintenance trick
One, protecting the toilet depends on the actual situation in the home, and if the water in our house is a hard water source, then care is to be taken, because there are more impurities in the water, so you must keep the water hole clean and avoid blocking your toilet。
When using toilets every day, care is taken not to throw hard matter into the toilet, which can cause toilet congestion and inconvenience。
Three of the toilets belong to the porcelain category, and what is more feared is that they will hit sharp objects, which will damage your toilet, and it is recommended that when you go to the toilet, be careful not to bring anything hard and avoid damage to the toilet。
4. Cleaning up, for less dirty toilets, a piece of toilet paper can be laid on the inside wall of the toilet and then sprayed with detergents or remaining cokes, and then washed off with water after a quiet hour, then with a brush. It's not just for the sake of being effective, it's for the sake of the face。
Each automatic flushing toilet contains a floating ball, which, as the water level in the toilet rises, produces increasing buoyancy, and when the water level rises to a predetermined level, the buoyancy of the plume is automatically pulled out of the plug through a plate structure. After the water is released, the plugs automatically enter the next round of recharge cycles with the spring。
The principle of automatic flushing of the bai devices in public health is very simple. It is an infrared launch and acceptance machine, and when a person is in front of a toilet, the infrared signal is placed on you by a receiver, which, after a simple pcl control, is treated as if someone was in the toilet, and then, through an electric control switch, controls the valve of a pump toilet, which opens up the stored water, thus acting as an automatic flush. Infrared is also a light wave, following the law of reflection of light, where objects are reflected when they are launched, and where the body or clothing is not absolutely smooth, so what happens after the attack is a flash reflection, the face of which is so large that it can be picked up by a small receiving device. The control mechanism for toilets pumped from the toilet was not a continuous signal, but was launched outward at a frequency at a time interval at which it did not send a signal, at which point the processor was handling the received signal to determine whether or not a person was using the sanitation facility. Then it may be strange that the bathroom space is relatively small, and what is the device to determine whether someone is using sanitary devices or the light waves reflected on the wall? This is determined by time, and although the speed of light transmission is very fast, there is also time when the processor determines whether the object is at a distance from itself by the time difference between the launch and the receipt of the light signal, and thus whether the person uses the sanitary facility or the light waves reflected on the wall. However, the determination of this time margin is not very intelligent, and as long as an object blocks a signal window at a close distance, it causes a miscalculation of the equipment, so it also washes automatically when someone passes through an automatic flush. The current technology is not incapable of achieving an accurate determination as to whether or not a flush toilet is being used, but to do so the cost of production of equipment will increase significantly, because the use of automatic flush toilets is very large, because higher costs and higher prices will lead to many public health spaces not choosing to be installed, with a greater impact on product promotion. When you open an automatic flush toilet, you find it is very simple, with about a fist-sized treatment facility that is powered by a regular battery, with an external connection to a signal window, embedded outside the toilet, simple construction and very low production costs, and is now widely used. The use of automatic flush toilets is on the one hand intended to be user-friendly and to improve the quality of services. On the other hand, the aim is to prevent a few from forgetting to flush or deliberately not to flush in order to keep the bathroom clean. The simple application of this structure to a wide range of small products is still very effective, and he is not as amazing as he thought。
The toilet is an indispensable tool for life in the bathroom, and many people don't know what the toilet is. The toilet principle is something you have to understand when you choose to buy it, and i'll tell you more about it. The main method of pumping toilets is that of iris, which is also the basis for drawing toilets. “push water” in a pump toilet means a s-shaped bend beneath a urinator, where when the water in the toilet exceeds the height of the s-barrel, the formation of a rainbow absorbs the water and stains of the urinator together. Until only a small amount of water was left, the rainbow was destroyed and a small amount of water left behind, forming the water seal. Ionic: iris sucking is caused by the difference in gravity and bits between liquid molecules. This means that water rises to a low level using poor water column pressure. The water is subject to different atmospheric pressures on the surface of the pipe, and the water will flow from one side of the pressure to the other side of the pressure, until the atmospheric pressure on both sides is equal, the water in the container becomes equal height and the water ceases to flow. The use of rainbow insinuation quickly removes water from the container. The flushing toilet consists of the following main components: taps, taps, seeps, plugs (in and out), flounders, hoses and levers. The role of the above components in work is to be ascertained. Pumping toilet (water tank) principles: when water discharges, pulls the shrub, which pulls out the plug by leverage. So the water can be released. When the water was released, it fell down and blocked the water. At that point, the float was also down due to the water surface and was at the bottom of the tank. And the fate of the flounder, the lever will pull up and the water into the tank. As the water rises, the float will gradually rise as a result of buoyancy until the water will be pressurized and blocked by leverage. It's filled with water. Think about what the spin button does. When a pipe leaks as a result of a failure (e. G. A plug cannot block the entrance or break the intake), the water in the tank will rise and eventually spill out. This problem is solved by the installation of a cavity pipe. When the water rises to the permeable pipe, the water flows from the permeable pipe into the toilet and does not spill over the tank. When the pipes are working normally, the water in the tanks does not reach the permeable pipe, so there is no fear that the water will run away。
The principle of automatic flushing of toilets is achieved by connecting infrared sensor switches to electromagnetic valves. Human thermal emission infrared sensors: the body has constant body temperature and works at 37 degrees with infrared rays of about 10um with a specific wavelength, and passive infrared probes detect about 10um from humans。
The pumped toilet consists of the following main components: taps, taps, seeps, plugs (in and out), floats, gyruss and levers, water rechargers, tanks, urinals (there are contours of connected water tanks)。
The basic rationale for pumping toilets is to use the gravity of the water to convert the water's potential to its kinetic energy, thereby holding the discharge into the sewers。
Clean up
1. Exorcism by vinegar: pouring out of the toilet a mixture of vinegar and water, so that after half a day of immersion, the mud will be washed out。
2. Sandpaper decompositation: rubbing toilet dirt with the most fine sandpaper to remove stains that the cleaning agent cannot remove。
3. Little soda detergent: swallow the little soda in the toilet and wash it with hot water for half an hour so the dirt can be washed away。
4. Floating powder solution decontaminator: first wipe with bleach powder solution, then wash with water。
